/usr/man/cat.1/rsh.1.Z(/usr/man/cat.1/rsh.1.Z)

NAME

     rsh -- remote shell

SYNOPSIS

     rsh [-45FGKdefnuxz] [-U string] [-p port] [-l username] [-P N|O] host
         [command]

DESCRIPTION

     rsh authenticates to the rshd(8) daemon on the remote host, and then exe-
     cutes the specified command.

     rsh copies its standard input to the remote command, and the standard
     output and error of the remote command to its own.

     Valid options are:

     -4, --krb4
             The -4 option requests Kerberos 4 authentication. Normally all
             supported authentication mechanisms will be tried, but in some
             cases more explicit control is desired.

     -5, --krb5
             The -5 option requests Kerberos 5 authentication. This is analo-
             gous to the -4 option.

     -K, --broken
             The -K option turns off all Kerberos authentication. The security
             in this mode relies on reserved ports. The long name is an indi-
             cation of how good this is.

     -n, --no-input
             The -n option directs the input from the /dev/null device (see
             the BUGS section of this manual page).

     -d      Enable setsockopt(2) socket debugging.

     -e, --no-stderr
             Don't use a separate socket for the stderr stream. This can be
             necessary if rsh-ing through a NAT bridge.

     -x, --encrypt
             The -x option enables encryption for all data exchange. This is
             only valid for Kerberos authenticated connections (see the BUGS
             section for limitations).

     -z      The opposite of -x.  This is the default, and is mainly useful if
             encryption has been enabled by default, for instance in the
             appdefaults section of /etc/krb5.conf when using Kerberos 5.

     -f, --forward
             Forward Kerberos 5 credentials to the remote host.  Also settable
             via appdefaults (see krb5.conf).

     -F, --forwardable
             Make the forwarded credentials re-forwardable.  Also settable via
             appdefaults (see krb5.conf).

     -l string, --user=string
             By default the remote username is the same as the local. The -l
             option or the username@host format allow the remote name to be
             specified.

     -n, --no-input
             Direct input from /dev/null (see the BUGS section).

     -p number-or-service, --port=number-or-service
             Connect to this port instead of the default (which is 514 when
             using old port based authentication, 544 for Kerberos 5 and non-
             encrypted Kerberos 4, and 545 for encrytpted Kerberos 4; subject
             of course to the contents of /etc/services).

     -P N|O|1|2, --protocol=N|O|1|2
             Specifies the protocol version to use with Kerberos 5.  N and 2
             select protocol version 2, while O and 1 select version 1. Ver-
             sion 2 is believed to be more secure, and is the default. Unless
             asked for a specific version, rsh will try both.  This behaviour
             may change in the future.

     -u, --unique
             Make sure the remote credentials cache is unique, that is, don't
             reuse any existing cache. Mutually exclusive to -U.

     -U string, --tkfile=string
             Name of the remote credentials cache. Mutually exclusive to -u.

     -x, --encrypt
             The -x option enables encryption for all data exchange. This is
             only valid for Kerberos authenticated connections (see the BUGS
             section for limitations).

     -z      The opposite of -x.  This is the default, but encryption can be
             enabled when using Kerberos 5, by setting the libdefaults/encrypt
             option in krb5.conf(5).

EXAMPLES

     Care should be taken when issuing commands containing shell meta charac-
     ters. Without quoting, these will be expanded on the local machine.

     The following command:

           rsh otherhost cat remotefile > localfile

     will write the contents of the remote remotefile to the local localfile,
     but:

           rsh otherhost 'cat remotefile > remotefile2'

     will write it to the remote remotefile2.

FILES

     /etc/hosts

SEE ALSO

     rlogin(1), krb_realmofhost(3), krb_sendauth(3), hosts.equiv(5),
     krb5.conf(5), rhosts(5), kerberos(8) rshd(8)

HISTORY

     The rsh command appeared in 4.2BSD.

AUTHORS

     This implementation of rsh was written as part of the Heimdal Kerberos 5
     implementation.

BUGS

     Some shells (notably csh(1)) will cause rsh to block if run in the back-
     ground, unless the standard input is directed away from the terminal.
     This is what the -n option is for.

     The -x options enables encryption for the session, but for both Kerberos
     4 and 5 the actual command is sent unencrypted, so you should not send
     any secret information in the command line (which is probably a bad idea
     anyway, since the command line can usually be read with tools like
     ps(1)).  Forthermore in Kerberos 4 the command is not even integrity pro-
     tected, so anyone with the right tools can modify the command.

HEIMDAL                        February 20, 2004                       HEIMDAL
See also sh(1)